logo

Could not compile stylesheet for simplistic. Using last compiled stylesheet.

How do you install u-boot? please help

posted in Uncategorized
Monday, October 17 2011, 04:53 AM
0
Please help. I seem to have managed to break my board. I have an igepv2. And I followed the instructions on the wiki about un-bricking it. It basically downloads a new version of the firmware with the poky sata distro and flashes the firmware memory thingy. Only problem is now all it does is boot straight into the poky distro. I want to be able to run the linaro distro which I have built and have on an sd card. but when I power the thing on it just goes directly to the jffs image I think with x-loader and boots that. Help! is there a way of putting u-boot back into the firmware so I can boot from sd cards again?
Responses (5)
  • Accepted Answer

    mcaro
    mcaro
    Offline
    Monday, October 17 2011, 06:25 PM - #permalink
    0
    Try to follow this howto, it not uses the OneNand for boot. [url=http://labs.igep.es/index.php/How_to_boot_from_MicroSD_Card]http://labs.igep.es/index.php/How_to_bo ... croSD_Card[/url] Always the board try to boot from microsd card before the onenand ...
    The reply is currently minimized Show
  • Accepted Answer

    Thursday, October 20 2011, 06:31 AM - #permalink
    0
    thanks for the reply This doco seems a little out of data, When you git clone x-loader and go to make it $/home/jdoe/igep-x-loader> make igep0020-sdcard_config i get make: *** No rule to make target `igep0020-sdcard_config\\\'. Stop. any ideas?
    The reply is currently minimized Show
  • Accepted Answer

    Thursday, October 20 2011, 08:16 AM - #permalink
    0
    And if you manage to get further down the page when you go to compile the kernel I get this $/home/jdoe/linux-omap-2.6> make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- igep0020_defconfig Can\\\'t find default configuration \\\"arch/arm/configs/igep0020_defconfig\\\"! any ideas?
    The reply is currently minimized Show
  • Accepted Answer

    mcaro
    mcaro
    Offline
    Thursday, October 20 2011, 09:38 AM - #permalink
    0
    About your first question, you should check the IGEP X-Loader howto: [url=http://labs.igep.es/index.php/The_IGEP_X-loader#Build_with_Ubuntu_Cross_Compiler_gcc_4.5.2]http://labs.igep.es/index.php/The_IGEP_ ... _gcc_4.5.2[/url] as you can see the latest version uses other configuration file: [code]make igep00x0_config[/code] And about your second question, you should check the kernel build howto: [url=http://labs.igep.es/index.php/Linux_Kernel_2.6.35.y]http://labs.igep.es/index.php/Linux_Kernel_2.6.35.y[/url] as use the right file config: [code]make ARCH=arm CROSS_COMPILE=[your cross compiler] igep00x0_defconfig[/code] Thank you, we will revise this howto and update the procedure for latest software versions ;)
    The reply is currently minimized Show
  • Accepted Answer

    Thursday, November 17 2011, 02:08 AM - #permalink
    0
    Cool that works Thanks for your help. Next question. How do I make the think now boot from onenand ? I assume it\\\'s some sort of copying of the boot partition to the mtd?
    The reply is currently minimized Show
Your Reply

SUPPORT


This email address is being protected from spambots. You need JavaScript enabled to view it.
This email address is being protected from spambots. You need JavaScript enabled to view it.
IGEP Community Wiki
IGEP Community Forum
IGEP Community Online Chat