Could not compile stylesheet for simplistic. Using last compiled stylesheet.
Discussions tagged Bootloader
-
IGEP COM MODULE boot problem
posted in IGEP COM MODULEHello, I tried to boot my igep0030-RE6 but with no success. I used: ./igep-media-create --mmc /dev/sdb --machine igep0030 --image demo-image-sato-igep00x0.tar.bz2 command to create my bootable SD Card. Under windows I only s... -
-
Which bootloader to use on IGEP COM? (June 2013)
Questionposted in IGEP COM MODULEI have some IGEP COM modules (igep0030) which have the Hynix DM3730 part fitted and was wondering whether to keep using this bootloader (v.2.5.0-2) which was last updated on your GIT repo 8 months ago. I noticed that your u-boot GIT repo... -
X-Loader splash image - DSS_DATA0 thru DSS_DATA5 always low
posted in IGEP COM MODULEHi! I'm trying to display an image on TFT lcd with x-loader or even a solid background color. My problem is that pin DSS_DATA0 thru DSS_DATA5 are always low (tested with scope) so blue colors are not displayed. Red and green works fine. ... -
J990 pins state during the boot process
posted in IGEPv2I'm working on a project with IGEPv2, it boots from the microSD Linaro operating system. I have a plaque attached with GPIOs J990 connector using pins 3 through 22. I'm using 8 input pins and 12 output pins, where I have connected some LE... -
Problem with igep-dsp-gst-framework-3_40_00
posted in IGEP DSP Gstreamer FrameworkHi, I'm trying to make/install igep-dsp-gst-framework-3_40_00.tar.bz2 on SDK VM for COM MODULE RE6 This thread has been very useful for some early troubles: http://forum.isee.biz/viewtopic.php?f=80&t=7208 When I... -
IGEPv2 RB1: igep.ini parameters
posted in IGEPv2Hi, what is the right value for the revision parameter in the igep.ini file for a IGEPv2 RB1 release? 0001 is right? Thanks Albano... -
Splash screen
posted in IGEP SDK Yocto (Toolchain and Firmware)Hello all I'm trying to display a splash screen when booting IGEPv2. So far I managed to replace the Tux logo when the kernel is booting, but I would like to display my picture earlier in the boot process. I know that it was ... -
Migrating from rev. B to rev. C: Boot sequence
posted in IGEPv2Hi all, I was using a rev. B board for several years and I've just upgraded to a rev. C board. It seems the boot procedure has changed quite a bit. I'm trying to launch a custom binary (not Linux). It's just a binary blob - ... -
430M memory limit in x-loader cfg
posted in IGEP SDK Yocto (Toolchain and Firmware)I'm just curious... why the memory size (kparams.mem parameter) is limited to 430M in igep.ini x-loader configuration file by default?... -
Error: Unsupported NAND Chip!
posted in SoftwareI bought an Igep v2 board (IGEP0020-RC6) and I try to follow the "Linux embedded training" course offered by free-electrons company. I encountered some problems during the compilation and installation of the X-Loader and U-Boot bo... -
IGEP-X-Loader 2.4.0-3
posted in IGEP SDK Yocto (Toolchain and Firmware)Hello, i have several dozens of IGEP0020 boards in the field, almost all RC1, im very happy with them, good hardware! In them i use x-loader+uboot Im at this moment prototyping another project also using IGEP0020 boards, now RC6 version... -
x-loader / u-boot download links
posted in IGEP SDK Yocto (Toolchain and Firmware)Hi! I was trying to follow the steps of "How to get the Ubuntu distribution" and I succeeded until I had to download the x-loader and u-boot from: -x-loader: -
Start problems with IGEP COM MODULE + PARIS
posted in IGEP PARISHi, I have a processor board IGEP COM Module on an expansion board IGEP PARIS and I have some problems at the beginning. First of all what I can see it is that the Ethernet port of the IGEP PARIS is not enabled from the start (I su... -
x-loader hangs on IGEPv2
posted in IGEPv2Hello all I am trying to boot an IGEPv2 RC6 with x-loader 1.4.4-3 and U-boot 2010.06-2 on SD card. X-loader hangs at "Reading boot sector". What I tried so far (with no success) : - Partition and format the SD card agai... -
Com Proton boot problem
posted in IGEP COM PROTONHi, yesterday I've received an Igep Com Proton + Paris Exp Board. First of all I've connected com proton to my PC through mini-USB cable (without exp board). Blue led remains on, and nothing happens (cdc_ether device not appears). So, I'v... -
IGEP-X-Loader 2.4.0-3
posted in IGEP SDK Yocto (Toolchain and Firmware)Hello, I trying to load the x-loader 2.4.3-3 in a IGEPv2 RB1, from a SDCard, but appear the message: Configuration file igep.ini not found or invalid (-1), using defaults The igep.ini file exist in the same folder. This message app...
- Page :
- 1