Could not compile stylesheet for simplistic. Using last compiled stylesheet.
Featured Topics
-
Java benchmarks of IGEP Technology devices
Announcementposted in AnnouncementsHi Community, We added a JAVA benchmark comparison in our wiki page, please be free to comment here ...
-
Replace Matchbox window manager
posted in Linux DistributionsDear ISEE Community: I have a problem with the Yocto operating system, that includes the matchbox as a window manager, that it's a problem for a project that I'm developing. I'm doing an application in Qt that I'm removing the frames. In... -
Creating a Ubuntu SDCard for IGEPv2
Questionposted in IGEPv2I'm trying to build a bootable SDCard for the IGEPv2 from the linaro images, here http://releases.linaro.org/images/12.03... -
using USB OTG as USB HOST
Issueposted in IGEP COM MODULEHi all i use an IGEP COM MODULE and i try to read an USB key via USB OTG port. the USB OTGID pin is tied to ground on the IGEP side. The Kernel version is 2.6.37.5. At the power up if the USB key is plugged all is OK an... -
UART1_RX pin on J960 not working on IGEPv2?
posted in IGEPv2The J960 UART1_RX - /dev/ttyO0 - does not seem to receive data. I did 2 tests: Test #1 I connected IGEPv2 pins J960-8, J960-9 and J960-6 to a DB9 connector through to a USB on Ubuntu machine The IGEPv2 UART1 - /dev/ttyO0 - s... -
QT Show image
Questionposted in IGEP COM MODULEDear ISEECommunity: I'm using the image of Yokto Firmware as operating system into my IGEP COM MODULE. My application will use QT Libraries and tools to make my application, because we are going to show some images using the HDMI. I've i... -
Telit
posted in IGEP BERLINDear IseeCommunity: I've bougth DM3730 COM Module and IGEP Berlin expansion boards. I've installed the fast boot demo(https://www.isee.biz/supp... -
transform igepv2 to NOWIFI model
posted in IGEPv2Dear forum In order to use GPIO 138,139, 137 for GPIO purpose , I want to know if it is out there some "pcb patch" that I can apply to transform my igepv2 boards to NOWIFI??? (appart from use kernel without libertas driver) ... -
changing ethernet MTU on IGEPv5
posted in IGEPv5Does the IGEPv5 ethernet interface allow changing the MTU size to support jumbo packets? For example, the default MTU size is 1500, but I want to change it to 7200. In linux this would be done with the command ifconfig eth0 mtu 7200 -
Does ISEE offer 3D models of their processor boards?
Questionposted in ISEE: Questions, Suggestions, DoubtsI need a model of the IGEPv5 to fit in an enclosure I have in SolidWorks and was hoping for a model.... -
IGEPv5 power requirements
Questionposted in Talk, Help, Share your ideas ...The IGEPv5 hardware manual states (page 63) that the 5V input is between 80mA and 6A, with typical around 2A. We didn't order a supply from ISEE, but are using a 1.5A supply we already have. Is this sufficient to boot up an IGEPv5 (full edition), ass... -
Is it correct that u-boot and u-boot-arm are out of sync?
posted in UncategorizedHi all, It all starts at: http://martinezjavier.wordpress.com/2012/09/11/adding-igepv2-rev-c-support-to-m... -
Streaming from IGEPV2 board to an android app
Issueposted in IGEP DSP Gstreamer FrameworkHi there, We are trying to stream a video from an analog camera connected on the expansion board of an IGEPV2 to an android tab. The poky distribution is installed on the IGEPV2. We managed to send the video from the IGEPV2 b... -
Web base administration system
Questionposted in IGEPv2Hello, I woul like to install a web base administration system on an IGEPV2 board with igep poky firmware. Anyone has already do this with webmin or with another software? Thanks Arnaud... -
Bluetooth on IGEP COM MODULE with kernel 3.3.0
Questionposted in IGEP COM MODULEHi together, I have a IGEP COM MODULE with kernel 3.3.0 running here. But I don't get bluetooth working. After stty -F /dev/ttyO1 ispeed 115200 ospeed 115200 cs8 -cstopb clocal -crtscts -parodd I try this... -
How to wire a gps (3.3v) serial port streaming NMEA data to igepv2
Questionposted in IGEPv2I have igepv2 revision C. I have a a console running ubuntu connected to the igepv2 (via USB to DB9 connector and via IDC-10 (AT-Everex) configuration) J960 connector. I am using ttyO2 (UART3) in my igepv2 kernel and do not want to disable it!!... -
Yocto rootfs double eth0 ip configuratio?
Questionposted in ISEE: Questions, Suggestions, DoubtsHello every body! I see in my igep with yocto Rootfs in flash, I have double ip for eth0: #ifconfig eth0 Link encap:Ethernet HWaddr B2:B0:14:B5:CD:00 inet addr:192.168.0.157 Bcast:192.168.0.255 Mask:255.255.255.0... -
gstreamer on igepv5
Clarificationposted in IGEPv5hello is it possible ? not found yet in the glsdk !... -
Poor wifi performance
posted in UncategorizedHi All, I am using IGEPv2 board with Linaro netbook edition and Igep 2.6.35.13 kernel. I also installed the X-Loader to get it working on 1GHz. Everything is fine, except wifi. I cannot get faster transfer speed than 600 kbit/sec. I am t... -
igepv5 cam
Clarificationposted in IGEPv5Is the IGEP CAM BIRD compatible with igepv5 CE ? or what else camera can be used along with it ?... -
IGEPv2 NOWIFI gpio 139, 138, 137
Clarificationposted in IGEPv2Dear forum and ISEE team Please I need some clarification in order to use GPIO 139, 138 and 137 in my IGEPv2 NOWIFI board It is possible to use this pins as inputs? I'm reading all the time value=1 ...
- Total Posts: 1465
- Total Resolved Posts: 225
- Total Unresolved Posts: 1243
- Total Users: 7522
- Latest Member: gysyxety
- Online Users: 32 other guests